Please wait a minute...
工程设计学报
工程设计学报
保质设计     
针对一种简易链长测量法的误差分析及改进方案
周英杰
舍弗勒投资（中国）有限公司，上海 201804
Error analysis and optimization for a simplified chain length measurement method
ZHOU Ying-jie
Schaeffler Holding （China） Co. Ltd.， Shanghai 201804， China
 全文: PDF(2502 KB)   HTML
摘要： 目前在链磨损试验中用于检验延伸率的一种简易链长测量方法在其计算过程中存在较大理论误差，面对日益多样化的测试任务不具有普遍有效性，有必要对其改进．将基于中心距测量的测量系统拆分成与中心距对应的绷直链部分和与测量设备接触的弯折链部分，对测量系统进行数学建模，同时考虑具体的测量时刻对测量误差的影响，对误差展开较为全面的分析，结果发现误差主要来源于用弧长代替折线的近似手段．随后提出的一种基于理论节距的改进算法经过理论分析和对照测试标准的计算证明，在整体误差上比原算法小1个数量级，能显著地提高简易测量法的精度以满足工程要求，拓展了其有效应用领域．此外，结合设备的误差分析还以提高精度为目标对测试工具的设计提出了建议．
关键词： 链长测量;  误差分析;  数学建模;  套筒链;  滚子链    
Abstract: Simplified chain length measurement method currently used in chain wear test for elongation calculation has relatively large theoretical error which cannot guarantee the effectiveness considering increased types of measurement requirement. The measurement system based on axial distance was  divided into two parts, where the part of chain was straighttight or bended. Then mathematical models were created for the system considering the influence of measurement timing on error. Based on error analysis, the approximation of polylines with arc was proved to be the main cause of the measurement error. A new calculation method with smaller error by an order of magnitude was suggested, which made the simplified measurement method meet the general requirement on accuracy. It was also proved to be correct by validation with test standards. The improvement on calculation alone is meaningful in specific application areas, and the accuracy can be further increased by applying error analysis on equipment design.
Key words: chain length measurement    error analysis    mathematical modeling    bush chain    roller chain
出版日期: 2014-06-28
作者简介: 周英杰(1982—)，男，上海人，中级工程师，同济大学硕士毕业，从事疲劳测试、统计分析和工程数学研究，E-mail：rekooneal@126.com.
服务　　
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章　　

引用本文:

周英杰. 针对一种简易链长测量法的误差分析及改进方案[J]. 工程设计学报, 10.3785/j.issn. 1006-754X.2014.03.003.

ZHOU Ying-jie. Error analysis and optimization for a simplified chain length measurement method. Chinese Journal of Engineering Design, 10.3785/j.issn. 1006-754X.2014.03.003.

链接本文:

https://www.zjujournals.com/gcsjxb/CN/10.3785/j.issn. 1006-754X.2014.03.003    或    https://www.zjujournals.com/gcsjxb/CN/Y2014/V21/I3/217

[1] 曾维俊, 于广东, 雷恒波, 王钟周, 孙海旋. 用于相位衬度CT成像的大型精密转台轴系设计与分析[J]. 工程设计学报, 2018, 25(2): 223-229.
[2] 方晓瑜, 赵宏强, 文国臣. 基于AMESim恒功率变量泵的仿真研究[J]. 工程设计学报, 2011, 18(6): 437-443.
[3] 贺 甲, 田学光, 张德龙, 田兴志. 基于休斯敦方法的机械手误差建模与分析[J]. 工程设计学报, 2010, 17(6): 439-443.